Tampere University of Technology

TUTCRIS Research Portal

Department of Intelligent Hydraulics and Automation

Research unit: Department

  1. Published

    Controller design of digital hydraulic flow control valve

    Huova, M., Plaska, M., Siivonen, L., Linjama, M., Walden, M., Vilenius, M. & Sere, K., 2009, The 11th Scandinavian International Conference on Fluid Power SICFP'09, Linköping, Sweden, June 2-4 2009. p. 15 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  2. Published

    Energy efficiency of three-chamber cylinder with digital valve system

    Huova, M., Laamanen, A. & Linjama, M., 2010, In : International Journal of Fluid Power. 11, 3, p. 15-22

    Research output: Contribution to journalArticleScientificpeer-review

  3. Published

    Control of three-chamber cylinder with digital valve system

    Huova, M. & Laamanen, A., 2009, Proceedings of The Second Workshop on Digital Fluid Power 12-13 November 2009, Linz, Austria. Scheidl, R. & Winkler, B. (eds.). p. 94-105 12 p.

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  4. Published

    Autonomous pallet picking of GIM machine

    Hyvönen, M., Ghabcheloo, R., Mantere, P., Kolu, A. & Huhtala, K., 2011, Proceedings of the 5th GIM Scientific Workshop at Aalto University School of Electrical Engineering 29.-30.11.2011. Espoo: Aalto University, p. 30-36 (GIM Scientific Workshop).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  5. Published

    Simulation as a tool for development of control and interface system module

    Hyvönen, M., Multanen, P. & Huhtala, K., 2008, 1st GIM Scientific Workshop at Helsinki University of Technology, 14.-15.8.2008. p. 87-91

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientific

  6. Published

    Towards automatic testing of control systems for intelligent mobile machines

    Hyvönen, M., Multanen, P., Mantere, P., Kolu, A., Vallas, A., Alanen, J. & Rantala, S., 2009, The 11th Scandinavian International Conference on Fluid Power SICFP'09, Linköping, Sweden, June 2-4 2009. p. 12 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  7. Published

    Improvement of total efficiency of hydrostatic transmission by using optimized control

    Ijas, M. & Mäkinen, E., 2008, Proceedings of the 7th JFPS International Symposium on Fluid Power, Toyama, September 15-18, 2008. Tanaka, Y. (ed.). p. 271-276

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  8. Published

    Digital hydraulic pressure control

    Ijas, M., Mäkinen, E. & Linjama, M., 2009, The 11th Scandinavian International Conference on Fluid Power SICFP'09, Linköping, Sweden, June 2-4 2009. p. 12 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  9. Published

    Development of an intelligent control user interface for autonomous machines

    Järä, J. & Hyvönen, M., 2009, The Second Workshop on Generic Intelligent Machines, May 14-15, 2009, Tampere University of Technology, Tampere, Finland. Huhtala, K. & Uusi-Heikkilä, J. (eds.). p. 8 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  10. Published

    Host activities in connection with the DTP2 test facility

    Järvenpää, J., Timperi, A., Tuominen, R. & Mattila, J., 2008, Espoo: VTT. 5 p. (VTT Publications; vol. 678)

    Research output: Book/ReportCommissioned reportProfessional

  11. Published

    A parameter study of a digital pump

    Jaurola, M. & Huhtala, K., 2010, Fluid Power and Motion Control (FPMC 2010), 15-17 September 2010, University of Bath, UK. Johnston, D. N. & Plummer, A. (eds.). p. 203-215

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  12. Published

    Valve parameter study in case of digital pump

    Jaurola, M., 2010, Proceedings of the 3rd GIM Scientific Workshop, February 17-18, 2010, Aalto University School of Science and Technology. Halme, A. & Pirttioja, T. (eds.). Espoo, p. 1-13 13 p.

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  13. Published

    Detection of errors and failures using intelligent interface during a teleoperation process on skid steered mobile machine

    Javier, M., Karhu, O. I., Uusisalo, J. R. A. & Huhtala, K. J., 2008, 3rd IEEE Conference on Industrial Electronics and Applications ICIEA 2008, 3-5 June 2008, Singapore. p. 326-330

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  14. Published

    On-board data transfer of automated heavy machinery

    Karhu, O. & Huhtala, K., 2011, Proceedings of the 8th JFPS International Symposium on Fluid Power, Okinawa 2011, October 25-28, 2011, Okinawa, Japan. Okinawa: JFPS international Symposium on Fluid Power, p. 144-150 (International Symposium on Fluid Power JFPS).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  15. Published

    Autonomous excavation

    Karhu, O., 2009, The Second Workshop on Generic Intelligent Machines, May 14-15, 2009, Tampere University of Technology, Tampere, Finland. Huhtala, K. & Uusi-Heikkilä, J. (eds.). p. 10 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  16. Published

    On-board system integration of a mobile machine with automated functions operating in a multi-machine environment

    Karhu, O., 2011, GIM - Generic Intelligent Machines, The 4th GIM Scientific Workshop, January 18-19, 2011, Tampere University of Technology, Tampere, Finland. Tampere: Tampere University of Technology, (GIM Scientific Workshop; vol. 4).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  17. Published

    Autonomous excavation using hydraulic mobile machine retrofitted with electronic control system

    Karhu, O., Uusisalo, J., Honkakorpi, J. & Huhtala, K., 2008, Proceedings of the 7th JFPS International Symposium on Fluid Power, Toyama 2008, September 15-18, 2008. Tanaka, Y. (ed.). p. 359-362

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  18. Published

    Measuring and Modelling Hydraulic Fluid Dynamics at High Pressure - Accurate and Simple Approach

    Karjalainen, J-P., Karjalainen, R. & Huhtala, K., 2012, In : International Journal of Fluid Power. 13, 2, p. 51-59

    Research output: Contribution to journalArticleScientificpeer-review

  19. Published

    Second order polynomial model for fluid dynamics in high pressure

    Karjalainen, J-P., Karjalainen, R., Huhtala, K. & Vilenius, M., 2009, Proceedings of the ASME 2009 Dynamic Systems and Control Conference (DSCC2009) October 12-14, 2009, Hollywood, California, USA. p. 7 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  20. Published

    Comparison of measured and predicted dynamic properties of different commercial hydraulic fluids

    Karjalainen, J-P., Karjalainen, R., Huhtala, K. & Vilenius, M., 2011, The Twelfth Scandinavian International Conference on Fluid Power, SICFP'11, May 18-20, 2011, Tampere, Finland. Sairala, H. & Koskinen, K. T. (eds.). Tampere: Scandinavian International Conference on Fluid Power, p. 281-296 (Scandinavian International Conference on Fluid Power SICFP; vol. 12, no. 2).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  21. Published

    High-Pressure Properties of Hydraulic Fluid Dynamics and Second Order Polynomial Prediction Method

    Karjalainen, J-P., 2011, Tampere: Tampere University of Technology. 83 p. (Tampere University of Technology. Publication; vol. 983)

    Research output: Book/ReportDoctoral thesisCollection of Articles

  22. Published

    Turvallisuus hydraulijärjestelmän öljynäytteenotossa ja mittauksessa

    Karjalainen, R., 2009, PAMAS 2009 käyttäjäpäivät 10.-11.2.2009, Öljyjärjestelmien hiukkaslaskentakoulutus, Tampereen teknillinen yliopisto, Tampere, Finland. Rinkinen, J., Multanen, P., Elo, L. & Niiranen, E. (eds.). p. 116-120

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientific

  23. Published

    Effect of fluid properties on power system dynamics

    Karjalainen, J-P., 2009, The Second Workshop on Generic Intelligent Machines, May 14-15, 2009, Tampere University of Technology, Tampere, Finland. Huhtala, K. & Uusi-Heikkilä, J. (eds.). p. 6 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  24. Published

    Energy efficient digital hydraulic solutions for mobile booms

    Karvonen, M., 2011, GIM - Generic Intelligent Machines, The 4th GIM Scientific Workshop, January 18-19, 2011, Tampere University of Technology, Tampere, Finland. Tampere: Tampere University of Technology, p. 1-4 4 p. (GIM Scientific Workshop; vol. 4).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  25. Published

    Simulation study - improving efficiency in mobile boom by using digital hydraulic power management system

    Karvonen, M., Heikkilä, M., Huova, M., Linjama, M. & Huhtala, K., 2011, The Twelfth Scandinavian International Conference on Fluid Power, SICFP'11, May 18-20, 2011, Tampere, Finland. Sairala, H. & Koskinen, K. T. (eds.). Tampere: Scandinavian International Conference on Fluid Power, p. 355-368 (Scandinavian International Conference on Fluid Power SICFP; vol. 12, no. 3).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  26. Published

    Recent advancements in miniature valve development

    Karvonen, M., Ketonen, M., Linjama, M. & Puumala, V., 2011, The Fourth Workshop on Digital Fluid Power, 21st-22nd November, 2011, Linz, Austria. Linz: DFP-Workshops, p. 90-103 14 p. (Workshop on Digital Fluid Power; vol. 4).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  27. Published

    A miniature needle valve

    Karvonen, M., Juhola, M., Ahola, V., Söderlund, L. & Linjama, M., 2010, Proceedings of the Third Workshop on Digital Fluid Power, October 13-14 2010, Tampere, Finland. Laamanen, A. & Linjama, M. (eds.). p. 61-78

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  28. Published

    A novel symmetric and bistable seat valve

    Karvonen, M., Uusitalo, J-P., Ahola, V., Linjama, M. & Vilenius, M., 2009, The 11th Scandinavian International Conference on Fluid Power SICFP'09, Linköping, Sweden, June 2-4 2009. p. 14 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  29. Published

    Hydraulitekniikka (1. p.)

    Kauranne, H., Kajaste, J. & Vilenius, M., 2008, Helsinki: WSOY.

    Research output: Book/ReportBookScientificpeer-review

  30. Published

    Development and design optimization of water hydraulic manipulator for ITER

    Kekäläinen, T., Mattila, J. & Virvalo, T., 2009, In : Fusion Engineering and Design. Vol. 84, 2-6, p. 1010-1014

    Research output: Contribution to journalArticleScientificpeer-review

  31. Published

    Implementation of a digital hydraulic valve system with Bosch Rexroth sec valves

    Ketonen, M., 2012, DFP 12, Proceedings of the fifth workshop on digital fluid power, October 24-25, 2012, Tampere, Finland. Laamanen, A. & Linjama, M. (eds.). Tampere: Tampere University of Technology. Department of Intelligent Hydraulics and Automation, p. 161-174 (Workshop on digital fluid power).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  32. Published

    Improving energy efficiency and productivity of existing hydraulic systems by retrofittable digital hydraulics

    Ketonen, M., 2012, GIM - Generic Intelligent Machines, Proceedings of the 6th GIM Scientific Workshop, November 7-8, 2012, Tampere, Finland. Huhtala, K. & Uusi-Heikkilä, J. (eds.). Tampere: Tampere University of Technology. Department of Intelligent Hydraulics and Automation, p. 63-66 (GIM Scientific Workshop).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  33. Published

    Digital Hydraulic Pressure Relief Function

    Ketonen, M., Huova, M., Heikkilä, M., Linjama, M., Boström, P. & Walden, M., 2012, Fluid Power and Motion Control, FPMC 2012, University of Bath, UK. Johnston, D. N. & Plummer, A. R. (eds.). Bath, United Kingdom: Centre for Power Transmission and Motion Control, University of Bath, ASME, p. 137-150 (Bath/ASME Symposium on Fluid Power and Motion Control).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  34. Published

    Calibration and compensation of deflections and compliances in remote handling equipment configurations

    Kivelä, T., Saarinen, H., Mattila, J., Hämäläinen, V., Siuko, M. & Semeraro, L., 2011, In : Fusion Engineering and Design. 86, 9-11, p. 2043-2046

    Research output: Contribution to journalArticleScientificpeer-review

  35. Published

    Adaptive dead zone compensation of proportional mobile valve

    Kivelä, T. & Mattila, J., 2011, The Twelfth Scandinavian International Conference on Fluid Power, SICFP'11, May 18-20, 2011, Tampere, Finland. Sairala, H. & Koskinen, K. T. (eds.). Tampere: Scandinavian International Conference on Fluid Power, p. 411-422 (Scandinavian International Conference on Fluid Power SICFP; vol. 12, no. 3).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  36. Published

    Method for automatic testing of control systems

    Kolu, A., Mantere, P., Vallas, A., Hyvönen, M. & Multanen, P., 2011, The Twelfth Scandinavian International Conference on Fluid Power, SICFP'11, May 18-20, 2011, Tampere, Finland. Sairala, H. & Koskinen, K. T. (eds.). Tampere: Scandinavian International Conference on Fluid Power, p. 111-127 17 p. (Scandinavian International Conference on Fluid Power SICFP; vol. 12, no. 2).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  37. Published

    Augmented reality for operator assistance

    Kolu, A., 2012, GIM - Generic Intelligent Machines, Proceedings of the 6th GIM Scientific Workshop, November 7-8, 2012, Tampere, Finland. Huhtala, K. & Uusi-Heikkilä, J. (eds.). Tampere: Tampere University of Technology. Department of Intelligent Hydraulics and Automation, p. 9-13 (GIM Scientific Workshop).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  38. Published

    Puuvirta-virtuaalinen ja simuloitu oppimisympäristö

    Kortemaa, A., Moisio, M., Punki, J., Palonen, T., Ranta, P., Leino, T., Alarotu, V., Koskinen, K. T. & Tohu, J., 2011

    Research output: Artistic and non-textual formSoftwareScientific

  39. Published

    Metviro

    Kortemaa, A., Mäkelä, T., Punki, J., Ranta, P., Palonen, T., Leino, T. & Koskinen, K. T., 2009

    Research output: Artistic and non-textual formSoftwareScientific

  40. Published

    Department of Intelligent Hydraulics and Automation, Tampere University of Technology, Finland

    Koskinen, K. T., 2010, In : Journal of the Japan Fluid Power System Society. 41, 1, p. 35-40

    Research output: Contribution to journalArticleScientificpeer-review

  41. Published

    M1-teknologialla voidaan rakentaa virtuaalisia oppimisympäristöjä ja konelaboratorioita

    Koskinen, K. T., Leino, T., Palonen, T. & Ranta, P., 2010, In : Fluid Finland. 2/2010, p. 18-20

    Research output: Contribution to journalArticleScientific

  42. Published

    Water Hydraulic

    Koskinen, K. T. & Vilenius, M., 2011, Handbook of Hydraulic Fluid Technology. Totten, G. E. & De Negri, V. J. (eds.). Boca Raton,FL: CRC Press, p. 723-757

    Research output: Chapter in Book/Report/Conference proceedingChapterScientificpeer-review

  43. Published

    Recognition of Operating States of Mobile Machine

    Krogerus, T., 2011, Proceedings of the 5th GIM Scientific Workshop at Aalto University School of Electrical Engineering 29.-30.11.2011. Espoo: Aalto University, p. 70-80 (GIM Scientific Workshop).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  44. Published

    Sensitivity analysis of data analysis process in hydraulic forklift

    Krogerus, T., Rokala, M. & Koskinen, K. T., 2011, Proceedings of the 8th JFPS International Symposium on Fluid Power, Okinawa 2011, October 25-28, 2011, Okinawa, Japan. Okinawa: JFPS international Symposium on Fluid Power, p. 571-578 (International Symposium on Fluid Power JFPS).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  45. Published

    Feature Extraction and Self-Organizing Maps in Condition Monitoring of Hydraulic Systems

    Krogerus, T., 28 Jan 2011, Tampere: Tampere University of Technology. 126 p. (Tampere University of Technology. Publication; vol. 949)

    Research output: Book/ReportDoctoral thesisMonograph

  46. Published

    Comparison of vibration and pressure signals for fault detection on water hydraulic proportional valve

    Krogerus, T., Pietikäinen, J. & Koskinen, K. T., 2008, Proceedings of the 7th JFPS International Symposium on Fluid Power, Toyama, September 15-18, 2008. Tanaka, Y. (ed.). p. 691-696

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  47. Published

    Applying self-organizing maps to condition monitoring of hydraulic systems

    Krogerus, T., 2010, Proceedings of the 3rd GIM Scientific Workshop, February 17-18, 2010, Aalto University School of Science and Technology. Halme, A. & Pirttioja, T. (eds.). p. 1-10 10 p.

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  48. Published

    From measurements data to information

    Krogerus, T., 2012, GIM - Generic Intelligent Machines, Proceedings of the 6th GIM Scientific Workshop , November 7-8, 2012, Tampere, Finland. Huhtala, K. & Uusi-Heikkilä, J. (eds.). Tampere: Tampere University of Technology. Department of Intelligent Hydraulics and Automation, p. 51-62 (GIM Scientific Workshop).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  49. Published

    Data analysis process of working hydraulics of small mobile machine

    Krogerus, T., Rokala, M. & Koskinen, K. T., 2012, In : International Journal of Fluid Power. 13, 3, p. 5-15

    Research output: Contribution to journalArticleScientificpeer-review

  50. Published

    Testing of data analysis process in hydraulic forklift

    Krogerus, T. & Koskinen, K. T., 2011, The Twelfth Scandinavian International Conference on Fluid Power, SICFP'11, May 18-20, 2011, Tampere, Finland. Sairala, H. & Koskinen, K. T. (eds.). Tampere: Scandinavian International Conference on Fluid Power, p. 105-234 130 p. (Scandinavian International Conference on Fluid Power SICFP; vol. 12, no. 3).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  51. Published

    Water hydraulic forklift with intelligent condition monitoring system

    Krogerus, T., Sairiala, H. & Koskinen, K. T., 2008, Proceedings of the 51st National Conference on Fluid Power March 12-14, 2008, IFPE 2008, Las Vegas, USA. p. 337-344

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  52. Published

    A low resolution digital hydraulic control application

    Kukkonen, S. & Mäkinen, E., 2012, Proceedings of the 13th Mechatronics Forum International Conference, September 17-19, 2012, Johannes Kepler University Linz, Austria, Advances in Mechatronics. Scheidl, R. & Jakoby, B. (eds.). Linz: TRAUNER VERLAG, p. 8 p (Mechatronics Forum; vol. 1/3).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  53. Published

    Hiukkasen puhtaammaksi -laboratorio hydraulikomponenttien puhtaustutkimuksiin

    Kuosku, M. & Rinkinen, J., 2011, In : Promaint. 25, 5, p. 42-45

    Research output: Contribution to journalArticleProfessional

  54. Published

    Mittaustuloksia kaupallisilla puhtaustestikaapeilla

    Kuosku, M., Pekkonen, J. & Rinkinen, J., 2012, KompuNW -verkostoseminaari TTY:ssa 9.10.2012. Tampere: Tampere University of Technology, IHA - Department of Intelligent Hydraulics and Automation, p. 1-15 15 p.

    Research output: Chapter in Book/Report/Conference proceedingConference contributionProfessional

  55. Published

    The means of optimizing digital valve system

    Laamanen, A., 2008, Proceedings of the First Workshop on Digital Fluid Power 3rd October, 2008, Tampere, Finland. Linjama, M. & Laamanen, A. (eds.). p. 89-99

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientific

  56. Published

    Proceedings of the fifth workshop on digital fluid power, October 24-25, 2012, Tampere, Finland

    Laamanen, A. (ed.) & Linjama, M. (ed.), 2012, Tampere: Tampere University of Technology. Department of Intellidgent Hydraulics and Automation.

    Research output: Book/ReportAnthologyScientificpeer-review

  57. Published

    Proceedings of the Third Workshop on Digital Fluid Power, October 13-14 2010, Tampere, Finland

    Laamanen, A. (ed.) & Linjama, M. (ed.), 2010, Tampere: Tampere University of Technology.

    Research output: Book/ReportAnthologyScientificpeer-review

  58. Published

    Digital flow control unit for controlling amount of water used for binding dust

    Laamanen, A., Anttonen, P. & Linjama, M., 2010, Proceedings of the Third Workshop on Digital Fluid Power, October 13-14 2010, Tampere, Finland. Laamanen, A. & Linjama, M. (eds.). p. 119-128

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  59. Published

    Minimization of state transition uncertainty in the digital valve system

    Laamanen, A., 2009, The Second Workshop on Generic Intelligent Machines, May 14-15, 2009, Tampere University of Technology, Tampere, Finland. Huhtala, K. & Uusi-Heikkilä, J. (eds.). p. 9 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  60. Published

    Minimization of state transition uncertainty in the digital valve system

    Laamanen, A., 2009, Tampere: Tampere University of Technology. 111 p. (Tampereen teknillinen yliopisto. Julkaisu; vol. 809)

    Research output: Book/ReportDoctoral thesisCollection of Articles

  61. Published

    Characteristics of digital hydraulic pressure reducing valve

    Lähteenmäki, T., Ijas, M. & Mäkinen, E., 2010, Fluid Power and Motion Control (FPMC 2010), 15-17 September 2010, University of Bath, UK. Johnston, D. N. & Plummer, A. R. (eds.). p. 69-82

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  62. Published

    Collaboration between design and production by exploiting VR/AR and PLM - case Metso Minerals

    Leino, S-P., Vehviläinen, M., Kiviranta, S., Mäkiranta, A., Nuutinen, P., Hokkanen, I., Multanen, P., Rantanen, P., Heikkilä, J. & Martikainen, T., 2010, Proceedings of the 3rd International Conference on Applied Human Factors and Ergonomics (AHFE), 17-20 July 2010, Miami, Florida, USA. Karwowski, W. & Salvendy, G. (eds.). p. 1-11 11 p.

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  63. Published

    On the flow and cavitation characteristics of water hydraulic seat valve structures

    Leino, T., 2008, Tampere: Tampere University of Technology. (Tampereen teknillinen yliopisto. Julkaisu; vol. 722)

    Research output: Book/ReportDoctoral thesisCollection of Articles

  64. Published

    Enhanced industrial maintenance work task planning by using virtual engineering tools and haptic user interfaces

    Leino, S-P., Lind, S., Poyade, M., Kiviranta, S., Multanen, P., Reyes-Lecuona, A., Mäkiranta, A. & Muhammad, A., 2009, In : Lecture Notes in Computer Science. 5622, p. 346-354

    Research output: Contribution to journalArticleScientificpeer-review

  65. Published

    Virtauksen perusilmiöt vesihydrauliikan istukkaventtiilissä

    Leino, T., 2008, In : Fluid Finland. 3, p. 12-15

    Research output: Contribution to journalArticleProfessional

  66. Published

    Virtual engineering and remote operation in design, training and completon of demanding maintenance work tasks in challenging industrial plants (VIRVO) - MASIT15

    Leino, S-P., Helin, K., Lind, S., Viitaniemi, H., Multanen, P., Mäkiranta, A., Lahtinen, J., Nuutinen, P., Heikkilä, J-M. & Martikainen, T., 2008, Tekes. 10 p.

    Research output: Book/ReportCommissioned reportProfessional

  67. Published

    Development of a virtual environment for promoting safety in machine maintenance

    Lind, S., Leino, S-P., Viitaniemi, J., Helin, K., Multanen, P., Mäkiranta, A. & Heikkilä, J., 2008, Proceedings of the 6th International Conference on Occupational Risk Prevention, ORP´2008, A Coruña, Galicia, Spain, May 14th, 15th & 16th, 2008. Mondelo, P., Karwowski, W., Saarela, K., Hale, A. & Occipinti, E. (eds.). p. 14 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  68. Published

    A virtual engineering based method for maintainability design

    Lind, S., Leino, S-P., Multanen, P., Mäkiranta, A. & Heikkilä, J., 2009, Maintenance Management Conference 2009, Fourth International Conference on Maintenance and Facility Management, Rome, Italy, 22-24.4.2009. p. 117-122

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  69. Published

    New alternative for digital pump-motor-transformer

    Linjama, M. & Tammisto, J., 2009, Proceedings of The Second Workshop on Digital Fluid Power, 12-13 November 2009, Linz, Austria. Scheidl, R. & Winkler, B. (eds.). p. 49-61

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  70. Published

    Fundamentals of Digital Microhydraulic

    Linjama, M., 2012, Proceedings of the 8th International Fluid Power Conference, Dresden, March 26-28, 2012. Dresden: Technische Universität Dresden, Institute of Fluid Power, p. 385-396 (International Fluid Power Conference; vol. 1).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  71. Published

    Comparison of digital hydraulic and traditional servo system in demanding water hydraulic tracking control

    Linjama, M., Seppälä, J., Mattila, J. & Vilenius, M., 2008, Fluid Power and Motion Control FPMC 2008, 10-12 September 2008, Bath, UK. Johnston, D. N. & Plummer, A. R. (eds.). p. 393-403

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  72. Published

    Digitaalihydrauliikan seminaarin suosio yllätti

    Linjama, M., 2008, In : Fluid Finland. 3, p. 36-37

    Research output: Contribution to journalArticleProfessional

  73. Published

    Hydraulic hybrids

    Linjama, M., 2011, GIM - Generic Intelligent Machines, The 4th GIM Scientific Workshop, January 18-19, 2011, Tampere University of Technology, Tampere, Finland. Tampere: Tampere University of Technology, p. 1-1 1 p. (GIM Scientific Workshop; vol. 4).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  74. Published

    Digital fluid power - state of the art

    Linjama, M., 2011, The Twelfth Scandinavian International Conference on Fluid Power, SICFP'11, May 18-20, 2011, Tampere, Finland. Sairala, H. & Koskinen, K. T. (eds.). Tampere: Scandinavian International Conference on Fluid Power, p. 331-354 (Scandinavian International Conference on Fluid Power SICFP; vol. 12, no. 3).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  75. Published

    Hydrauliikan aika ei ole ohi - The time of hydraulics is not over

    Linjama, M., 2012, In : Fluid Finland. 11, 2, p. 10-12

    Research output: Contribution to journalArticleProfessional

  76. Published

    Digitaalihydrauliikka tulee!

    Linjama, M., 2010, In : Metsäalan ammattilehti. 5, p. 88-89

    Research output: Contribution to journalArticleProfessional

  77. Published

    Matkaraportti: Digitaalihydrauliikan seminaari marraskuisessa Linzissä

    Linjama, M., 2010, In : Fluid Finland. 1/2010, p. 12-14

    Research output: Contribution to journalArticleScientific

  78. Published

    Digital hydraulics research at IHA

    Linjama, M., 2008, Proceedings of the First Workshop on Digital Fluid Power 3rd October, 2008, Tampere, Finland. Linjama, M. & Laamanen, A. (eds.). p. 7-30

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientific

  79. Published

    Laitteisto, ohjauspiiri ja menetelmä paineen ja tilavuusvirran tuottamiseksi

    Linjama, M., Tammisto, J., Huhtala, K. & Vilenius, M., 2010, Patent No. Pat. FI 121090 B, Priority date 30 Jun 2010, Priority No. (21) FI 20085242

    Research output: PatentScientific

  80. Published

    Digital microhydraulics

    Linjama, M. & Karvonen, M., 2008, Proceedings of the First Workshop on Digital Fluid Power 3rd October, 2008, Tampere, Finland. Linjama, M. & Laamanen, A. (eds.). p. 141-152

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientific

  81. Published

    Proceedings of the First Workshop on Digital Fluid Power 3rd October, 2008 Tampere, Finland

    Linjama, M. (ed.) & Laamanen, A. (ed.), 2008, Tampere University of Technology.

    Research output: Book/ReportAnthologyScientificpeer-review

  82. Published

    Discussion: Is the future of fluid power digital? Response

    Linjama, M., Scheidl, R. & Schmidt, S., 2012, In : Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering. 226, I6, p. 726-727

    Research output: Contribution to journalArticleScientific

  83. Published

    Energy saving digital hydraulics

    Linjama, M., 2009, Proceedings of The Second Workshop on Digital Fluid Power, 12-13 November 2009, Linz, Austria. Scheidl, R. & Winkler, B. (eds.). p. 5-20

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  84. Published

    Secondary controlled multi-chamber hydraulic cylinder

    Linjama, M., Vihtanen, H-P., Sipola, A. & Vilenius, M., 2009, The 11th Scandinavian International Conference on Fluid Power SICFP'09, Linköping, Sweden, June 2-4 2009. p. 15 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  85. Published

    Modelling of flow characteristics of on/off valves

    Linjama, M., Huova, M. & Karvonen, M., 2012, DFP 12, Proceedings of the fifth workshop on digital fluid power, October 24-25, 2012, Tampere, Finland. Laamanen, A. & Linjama, M. (eds.). Tampere: Tampere University of Technology, Department of Intelligent Hydraulics and Automation, p. 209-222 (Workshop on digital fluid power).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  86. Published

    Tavoitteena häviötön hydrauliikka

    Linjama, M., 2009, In : Fluid Finland. 3-4, p. 12-17

    Research output: Contribution to journalArticleProfessional

  87. Published

    Model-based pressure control with digital valve system

    Linjama, M. & Lahtinen, J., 2011, The Fourth Workshop on Digital Fluid Power, 21st-22nd November, 2011, Linz, Austria. Linz: DFP-Workshops, p. 26-38 (Workshop on Digital Fluid Power; vol. 4).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  88. Published

    Digital hydraulic power management system - towards lossless hydraulics

    Linjama, M. & Huhtala, K., 2010, Proceedings of the Third Workshop on Digital Fluid Power, October 13-14 2010, Tampere, Finland. Laamanen, A. & Linjama, M. (eds.). p. 5-22

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  89. Published

    Digital pump-motor with independent outlets

    Linjama, M. & Huhtala, K., 2009, The 11th Scandinavian International Conference on Fluid Power SICFP'09, Linköping, Sweden, June 2-4 2009. p. 16 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  90. Published

    Digitaalisen mikrohydrauliikan sovellussatoa

    Linjama, M., 2009, In : Fluid Finland. 2/2009, p. 30-31

    Research output: Contribution to journalArticleProfessional

  91. Published

    Digital hydraulics - Towards perfect valve technology

    Linjama, M. & Vilenius, M., 2008, In : Ventil - Journal for Hydraulics, Automation and Mechatronics. 14, 2, p. 138-148

    Research output: Contribution to journalArticleScientificpeer-review

  92. Published

    Digital schlägt Analog um 40%

    Linjama, M., 2008, In : Fluid. 7-8/2008, p. 12-13

    Research output: Contribution to journalArticleProfessional

  93. Published

    Digitaalihydrauliikan kuulumiset

    Linjama, M., 2008, In : Fluid Finland. 2, p. 8-10

    Research output: Contribution to journalArticleProfessional

  94. Published

    Design and implementation of digital hydraulic synchronization and force control system

    Linjama, M., Hopponen, V., Ikonen, A., Rintamäki, P., Vilenius, M. & Pietola, M., 2009, The 11th Scandinavian International Conference on Fluid Power SICFP'09, Linköping, Sweden, June 2-4 2009. p. 13 p

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  95. Published

    Online minimization of power losses in distributed digital hydraulic valve system

    Linjama, M., Huova, M. & Vilenius, M., 2008, Proceedings of the 6th International Fluid Power Conference Dresden, Fluid Power in Motion, 6iFK, April 1.-2.2008, Dresden. p. 157-171

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  96. Published

    Virtuaalinen konelaboratorio työkonejärjestelmien opetukseen: Lihaako -projekti. Smart Simulators -tutkimusryhmä

    Mäkelä, T., Nurmi, J., Punki, J., Ranta, P., Tebest, T., Leino, T., Palonen, T., Helminen, M., Markkula, M. & Koskinen, K. T., 2010

    Research output: Artistic and non-textual formSoftwareScientific

  97. Published

    Concept design of the cassette toroidal mover

    Mäkinen, H., Järvenpää, J., Valkama, P., Väyrynen, J., Amjad, F., Siuko, M., Mattila, J., Semeraro, L. & Esque, S., 2011, In : Fusion Engineering and Design. 86, 9-11, p. 2092-2095

    Research output: Contribution to journalArticleScientificpeer-review

  98. Published

    Enhanced mobile machine assembly and maintainability evaluation using virtual and augmented reality

    Mäkiranta, A., Nuutinen, P., Multanen, P., Hyvönen, M., Leino, S-P., Kiviranta, S. & Vehviläinen, M., 2011, The Twelfth Scandinavian International Conference on Fluid Power, SICFP'11, May 18-20, 2011, Tampere, Finland. Tampere: Scandinavian International Conference on Fluid Power, p. 295-304 (Scandinavian International Conference on Fluid Power SICFP; vol. 12, no. 1).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  99. Published

    Method and tools for machine maintainability design in VE

    Mäkiranta, A. V., Multanen, P., Leino, S-P. S. & Lind, S. M., 2009, The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Dublin, Ireland, 23-25 June 2009. p. 877-888

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

  100. Published

    Utilization of the hydraulic engineering design information for semi-automatic simulation model generation

    Markkula, M., Rokala, M., Palonen, T., Alarotu, V., Helminen, M., Koskinen, K. T., Salonen, J., Nykänen, O., Ranta, P. & Pohjolainen, S., 2011, The Twelfth Scandinavian International Conference on Fluid Power, SICFP'11, May 18-20, 2011, Tampere, Finland. Sairala, H. & Koskinen, K. T. (eds.). Tampere: Scandinavian International Conference on Fluid Power, p. 443-458 (Scandinavian International Conference on Fluid Power SICFP; vol. 12, no. 3).

    Research output: Chapter in Book/Report/Conference proceedingConference contributionScientificpeer-review

ID: 21447