Department of Mechanical Engineering and Industrial Systems
Research unit: Department
- A1 Journal article-refereed
- Published
A numerical model for the calculation of fretting fatique crack initiation for a smooth line contact
Lehtovaara, A., Lönnqvist, C. & Mäntylä, A., 2010, In : Tribologia - Finnish Journal of Tribology. 29, 1, p. 7-16Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Optimum geometry of fixed volume plate fin for maximizing heat transfer
Karvinen, R. & Karvinen, T., 2010, In : International Journal of Heat and Mass Transfer. 53, 23-24, p. 5381-5385Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Nonlinear vibrations in a covered roll system with viscoelastic contact
Yuan, L. & Järvenpää, V-M., 2009, In : Communications in Nonlinear Science and Numerical Simulation. 14, 7, p. 3170-3178Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Geometric return algorithm for non-associated plasticity with multiple yield planes extended to linear softening/hardening models
Saksala, T., 2009, In : Rakenteiden mekaniikka. 42, 2, p. 83-98Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Experimental simulation of gear contact along the line of action
Kleemola, J. & Lehtovaara, A., 2009, In : Tribology International. 42, 10, p. 1453-1459Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Total Lagrangian beam element with C1-continuous slide-spring
Marjamäki, H. & Mäkinen, J., 2009, In : Computers & Structures. 87, 9-10, p. 534-542Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Graph-based selection of orchestrator paths in manufacturing lines
Popescu, C. & Martinez Lastra, J. L., 2009, In : International Journal of Computational Intelligence in Control. 1, 1, p. 57-69Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Product variety and reliability
Murthy, D. N. P., Hagmark, P-E. & Virtanen, S., 2009, In : Reliability Engineering and System Safety. 94, 10, p. 1601-1608Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Wear resistance of laser remelted thermally sprayed coatings
Surzhenkov, A., Kulu, P., Tarbe, R., Mikli, V., Sarjas, H. & Latokartano, J., 2009, In : Estonian Journal of Engineering. 15, 4, p. 318-328Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Ontologies for production automation
Martinez Lastra, J. L. & Delamer, I. M., 2009, In : Lecture Notes in Computer Science. 4891, p. 276-289Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Pulsed laser machining implemented with piezoelectric actuator
Kumpulainen, T., Karjalainen, I., Prusi, T., Hölsä, J., Heikkilä, R. & Tuokko, R., 2009, In : International Journal of Optomechatronics. 3, 1, p. 1-17 17 p.Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Development of a test device for the evaluation of fretting in point contact
Pasanen, A., Järvisalo, S., Lehtovaara, A. & Rabb, R., 2009, In : Lubrication Science. 21, 2, p. 41-52Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
A new concept for count distributions
Hagmark, P-E., 2009, In : Statistics and Probability Letters. 79, 8, p. 1120-1124Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Investment in new product reliability
Murthy, D. N. P., Rausand, M. & Virtanen, S., 2009, In : Reliability Engineering and System Safety. 94, 10, p. 1593-1600Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Friction behavior of quenched and tempered steel in partial and gross slip conditions in fretting point contact
Pasanen, A., Lehtovaara, A., Rabb, R. & Riihimäki, P., 2009, In : Wear. 267, 12, p. 2200-2207Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
On the fretting fatigue behavior of quenched and tempered steel in smooth point contact
Pasanen, A., Lehtovaara, A., Rabb, R. & Riihimäki, P., 2009, In : Tribologia - Finnish Journal of Tribology. 28, 3-4, p. 26-37Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Runtime modeling of flow for dynamic deadlock-free scheduling in service-oriented factory automation systems
Popescu, C., Cavia Soto, M. & Martinez Lastra, J. L., 2009, In : IETE Technical Review. 26, 3, p. 203-212Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Structural reasoning: An approach to the evaluation of system state spaces
Lobov, A. & Martinez Lastra, J. L., 2009, In : International Journal of Computational Intelligence in Control. 1, 1, p. 7-14Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
A parameterized numerical method for generating discrete helical gear tooth surface allowing non-standard geometry
Hedlund, J. & Lehtovaara, A., 2008, In : Proceedings of the institution of Mechanical Engineers Part C: Journal of Mechanical Engineering Science. 222, 6, p. 1033-1038Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
- Published
Testing method for the evaluation of parametric excitation of cylindrical gears
Lehtovaara, A. & Hedlund, J., 2008, In : Nondestructive Testing and Evaluation. 23, 4, p. 285-299Research output: Contribution to journal › Article › Scientific › peer-review
Full text:
ID: 22256