Tampere University of Technology

TUTCRIS Research Portal

Abrasive-Erosive Wear of Thermally Sprayed Coatings from Experimental and Commercial Cr3C2-Based Powders

Research output: Contribution to journalArticleScientificpeer-review

Standard

Abrasive-Erosive Wear of Thermally Sprayed Coatings from Experimental and Commercial Cr3C2-Based Powders. / Sarjas, Heikki; Surzhenkov, Andrei; Juhani, Kristjan; Antonov, Maksim; Adoberg, Eron; Kulu, Priit; Viljus, Mart; Traksmaa, Rainer; Matikainen, Ville; Vuoristo, Petri.

In: Journal of Thermal Spray Technology, Vol. 26, No. 8, 2017, p. 2020–2029.

Research output: Contribution to journalArticleScientificpeer-review

Harvard

Sarjas, H, Surzhenkov, A, Juhani, K, Antonov, M, Adoberg, E, Kulu, P, Viljus, M, Traksmaa, R, Matikainen, V & Vuoristo, P 2017, 'Abrasive-Erosive Wear of Thermally Sprayed Coatings from Experimental and Commercial Cr3C2-Based Powders', Journal of Thermal Spray Technology, vol. 26, no. 8, pp. 2020–2029. https://doi.org/10.1007/s11666-017-0638-2

APA

Sarjas, H., Surzhenkov, A., Juhani, K., Antonov, M., Adoberg, E., Kulu, P., ... Vuoristo, P. (2017). Abrasive-Erosive Wear of Thermally Sprayed Coatings from Experimental and Commercial Cr3C2-Based Powders. Journal of Thermal Spray Technology, 26(8), 2020–2029. https://doi.org/10.1007/s11666-017-0638-2

Vancouver

Sarjas H, Surzhenkov A, Juhani K, Antonov M, Adoberg E, Kulu P et al. Abrasive-Erosive Wear of Thermally Sprayed Coatings from Experimental and Commercial Cr3C2-Based Powders. Journal of Thermal Spray Technology. 2017;26(8):2020–2029. https://doi.org/10.1007/s11666-017-0638-2

Author

Sarjas, Heikki ; Surzhenkov, Andrei ; Juhani, Kristjan ; Antonov, Maksim ; Adoberg, Eron ; Kulu, Priit ; Viljus, Mart ; Traksmaa, Rainer ; Matikainen, Ville ; Vuoristo, Petri. / Abrasive-Erosive Wear of Thermally Sprayed Coatings from Experimental and Commercial Cr3C2-Based Powders. In: Journal of Thermal Spray Technology. 2017 ; Vol. 26, No. 8. pp. 2020–2029.

Bibtex - Download

@article{52bd66bdb95f4d3e87227cd55c518405,
title = "Abrasive-Erosive Wear of Thermally Sprayed Coatings from Experimental and Commercial Cr3C2-Based Powders",
abstract = "In this paper, high-velocity oxy-fuel sprayed coatings from experimental Cr3C2-Ni powder produced by mechanically activated thermal synthesis and disintegrator milling are compared with coatings from commercial Cr3C2-NiCr powder under room- and elevated-temperature abrasive-erosive wear (AEW) conditions. In a room-temperature AEW test, the coating made from the experimental powder had wear rates that were 1.1-5.3 times higher than the coating from the commercial powder; this difference was the lowest at the highest impact velocity (80 m s−1). Under AEW tests at elevated temperature (300 and 550 °C), the coating made from the experimental powder exhibited wear rates that were 1.2-2.8 times higher in comparison with that made from the commercial powder, but this difference was smaller under an oblique impact angle (30°) and higher temperature conditions. The reasons for the lower resistance against AEW of the coating made from the experimental powder were found to be its lower ability to resist plastic indentation and deformation as well as lower indentation fracture toughness at room temperature, weaker bonding between the matrix and reinforcement and probably lower mechanical properties as well as unfavourable residual stresses at elevated temperatures.",
keywords = "abrasive-erosive wear, CrC-based cermet, elevated temperature, mechanically activated thermal synthesis, room temperature, thermal spraying",
author = "Heikki Sarjas and Andrei Surzhenkov and Kristjan Juhani and Maksim Antonov and Eron Adoberg and Priit Kulu and Mart Viljus and Rainer Traksmaa and Ville Matikainen and Petri Vuoristo",
year = "2017",
doi = "10.1007/s11666-017-0638-2",
language = "English",
volume = "26",
pages = "2020–2029",
journal = "Journal of Thermal Spray Technology",
issn = "1059-9630",
publisher = "ASM International",
number = "8",

}

RIS (suitable for import to EndNote) - Download

TY - JOUR

T1 - Abrasive-Erosive Wear of Thermally Sprayed Coatings from Experimental and Commercial Cr3C2-Based Powders

AU - Sarjas, Heikki

AU - Surzhenkov, Andrei

AU - Juhani, Kristjan

AU - Antonov, Maksim

AU - Adoberg, Eron

AU - Kulu, Priit

AU - Viljus, Mart

AU - Traksmaa, Rainer

AU - Matikainen, Ville

AU - Vuoristo, Petri

PY - 2017

Y1 - 2017

N2 - In this paper, high-velocity oxy-fuel sprayed coatings from experimental Cr3C2-Ni powder produced by mechanically activated thermal synthesis and disintegrator milling are compared with coatings from commercial Cr3C2-NiCr powder under room- and elevated-temperature abrasive-erosive wear (AEW) conditions. In a room-temperature AEW test, the coating made from the experimental powder had wear rates that were 1.1-5.3 times higher than the coating from the commercial powder; this difference was the lowest at the highest impact velocity (80 m s−1). Under AEW tests at elevated temperature (300 and 550 °C), the coating made from the experimental powder exhibited wear rates that were 1.2-2.8 times higher in comparison with that made from the commercial powder, but this difference was smaller under an oblique impact angle (30°) and higher temperature conditions. The reasons for the lower resistance against AEW of the coating made from the experimental powder were found to be its lower ability to resist plastic indentation and deformation as well as lower indentation fracture toughness at room temperature, weaker bonding between the matrix and reinforcement and probably lower mechanical properties as well as unfavourable residual stresses at elevated temperatures.

AB - In this paper, high-velocity oxy-fuel sprayed coatings from experimental Cr3C2-Ni powder produced by mechanically activated thermal synthesis and disintegrator milling are compared with coatings from commercial Cr3C2-NiCr powder under room- and elevated-temperature abrasive-erosive wear (AEW) conditions. In a room-temperature AEW test, the coating made from the experimental powder had wear rates that were 1.1-5.3 times higher than the coating from the commercial powder; this difference was the lowest at the highest impact velocity (80 m s−1). Under AEW tests at elevated temperature (300 and 550 °C), the coating made from the experimental powder exhibited wear rates that were 1.2-2.8 times higher in comparison with that made from the commercial powder, but this difference was smaller under an oblique impact angle (30°) and higher temperature conditions. The reasons for the lower resistance against AEW of the coating made from the experimental powder were found to be its lower ability to resist plastic indentation and deformation as well as lower indentation fracture toughness at room temperature, weaker bonding between the matrix and reinforcement and probably lower mechanical properties as well as unfavourable residual stresses at elevated temperatures.

KW - abrasive-erosive wear

KW - CrC-based cermet

KW - elevated temperature

KW - mechanically activated thermal synthesis

KW - room temperature

KW - thermal spraying

U2 - 10.1007/s11666-017-0638-2

DO - 10.1007/s11666-017-0638-2

M3 - Article

VL - 26

SP - 2020

EP - 2029

JO - Journal of Thermal Spray Technology

JF - Journal of Thermal Spray Technology

SN - 1059-9630

IS - 8

ER -